Verilen alınan beğenileri görün
Beğendiğin mesajlar
Mesaj bilgileri |
Hayır. beğenilere |
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
Sayın metroloji16 dosyanın ne olduğunu anlamadım. edit window dan kopyalanıp yapıştırılmış gibi
Taner
Edit / Preferences / Edit Window Layout tıkla Show Header / Footer çentikli olduğuna emin ol.
Burayı çentiklediğinde elogo.dat doyası içindeki bilgiler Edit Window ve Report Window ekranlarında gözükecektir.
29 Temmuz 2015, 13:38:56
|
1
|
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
elogo.dat Türkçeleştirmek ve Düzenlemek için:
aşağıdaki yoldan dosyayı bulun.
C:\Program Files (x86)\WAI\PC-DMIS 2010 MR2\elogo.dat
dosyayı notepad ile açın ve bilgileri istediğiniz gibi değiştirin.
# dosyayla oynamadan önce bir yedeğini almayı UNUTMAYINIZ. # Sadece koyu olanları değiştiriniz.
END OF MEASUREMENT FOR ölçüm raporu sonu değiştirebilirsiniz. PN=#PARTN program no DWG=#DRWN Resim No SN=#SERIALN Seri no TOTAL # OF MEAS =#NMEAS toplam ölçüm OUT OF TOL =#NOUT tol dışı OF HOURS =#ELAPSTIM ölçüm süresi
29 Temmuz 2015, 14:06:49
|
1
|
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
elogo.dat Türkçeleştirmek ve Düzenlemek için:
aşağıdaki yoldan dosyayı bulun.
C:\Program Files (x86)\WAI\PC-DMIS 2010 MR2\elogo.dat
dosyayı notepad ile açın ve bilgileri istediğiniz gibi değiştirin.
# dosyayla oynamadan önce bir yedeğini almayı UNUTMAYINIZ. # Sadece koyu olanları değiştiriniz.
END OF MEASUREMENT FOR ölçüm raporu sonu değiştirebilirsiniz. PN=#PARTN program no DWG=#DRWN Resim No SN=#SERIALN Seri no TOTAL # OF MEAS =#NMEAS toplam ölçüm OUT OF TOL =#NOUT tol dışı OF HOURS =#ELAPSTIM ölçüm süresi
Merhaba Harek yukardaki paylastıgım dosya hazır dosya dat dosyası olarak paylaşımına site izin vermedigi için text dosyasına cevirdim sadece dosyayı indirip not defterinde acıp degişmesini istedigi ölçümü yapan veya sizin paylaştıgınız detayları düzeltip pcdmis dosyasına txt uzantısını dat olarak ddegiştirip kopyaladıgında olur diye tahmin ediyorum ..
29 Temmuz 2015, 14:12:39
|
1
|
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
içinde elogo dosyasında olması gerekmeyen yazılar olduğu için onu yazdım. Pcdmis programı hata verebilir.
29 Temmuz 2015, 14:16:34
|
1
|
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
Ben kullanıyorum bende herhangi bir hata vermiyor aynı sekilde kendi kullandıgım e logoyu kopyaladım ama tabi versiyon farkı veya farklı şeyler oluşurda hata verirmi siz ustalar daha iyi bilirsiniz ..
29 Temmuz 2015, 14:18:38
|
1
|
Ynt: Pc dmiste out of toleransların sayısını otomatik bulma...
ekteki dosya işinizi görecektir.
30 Temmuz 2015, 11:43:42
|
1
|
PC-DMIS yazılımı Windows'un hangi sürümleri üzerinde çalışacak?
Yazılım Sürümü | Uyumlu sistemler | PC-DMIS 2014.1** (32 and 64-bit versions) | Windows 7, and 8 | PC-DMIS 2014** (32 and 64-bit versions) | Windows 7, and 8 | PC-DMIS 2013 MR1** (32 and 64-bit versions) | Windows 7, and 8 | PC-DMIS 2013 | Windows 7 | PC-DMIS 2012 | Windows XP and Windows 7 | PC-DMIS 2011 | Windows XP and Windows 7 | PC-DMIS 2010 | Windows XP and Windows 7 | PC-DMIS 2009 | Windows XP | PC-DMIS 4.3 | Windows XP | PC-DMIS 4.2 | Windows 2000 and Windows XP | PC-DMIS 4.1 | Windows 2000 and Windows XP (32-bit only) | PC-DMIS 4.0 | Windows 2000 and Windows XP (32-bit only) | *Note: Due to a technical limitation in Windows. 32bit and 64 bit applications cannot interact. Therefore Direct CAD Interfaces, some machine interfaces, and other software may require the use of the 32-bit versions of software. **Note: PC-DMIS 2014 and PC-DMIS 2013 MR1 are both available in both 32 bit and 64 bit versions which allows them to use larger memory spaces, and interface with 32 or 64 bit versions of other software within Windows. Please see your version's full system requirements Linklere izin verilmiyor.
Üye Ol ya da Giriş Yap.
Alıntı:Linklere izin verilmiyor.
Üye Ol ya da Giriş Yap
21 Ağustos 2015, 08:21:18
|
1
|
PC-DMIS 2015.0 sistem gereksinimleri
PC-DMIS 2015.0 operates under the following:
32-bit and 64-bit Vista 32-bit and 64-bit Windows 7 32-bit and 64-bit Windows 8 and 8.1 No other operating systems are supported. Windows XP support: Beginning with v2012 MR1, support will be phased out for the Windows XP operating system. While this version likely runs fine in XP, it will not be tested under the XP operating system. Also note that some parts of the user interface do not appear optimally in XP. Support will be completely dropped in 2016.
IMPORTANT: When using third-party drivers, you should contact your local Hexagon representative to ensure operating system compatibility.
IMPORTANT: Running PC-DMIS inside a Virtual Machine (VM) is not supported. Notes: PC-DMIS Vision machines do not support 32-bit and 64-bit Windows 8.
The Matrox Framegrabber PC-DMIS Vision hardware component does not support a 64-bit operating system. Advantages of 64-bit: Customers with the x64-bit version of CAD packages need the 64-bit version of PC-DMIS in order to use Direct CAD Interfaces (DCI) to connect to the packages. The 64-bit version of PC-DMIS can use all of the physical memory that is available on the computer. The 32-bit version of PC-DMIS can only use the first 2 GB. Therefore, customers with large CAD or measurement routines are advised to use the x64-bit version. .NET Framework Microsoft .NET 4.0 for Windows 7 Microsoft .NET 4.5 for Windows 8
RAM
4 GB of RAM or higher (4 GB is the highest amount of memory capable on a 32- bit OS)
The size of the CAD data file and the tessellation multiplier value used affect the amount of memory needed. These both affect the amount of tessellated facets needed to display the model. The smaller the tessellation multiplier value used, the more memory needed for the facets. For large CAD models, this could cause an "Out Of Memory" error. If this occurs, the current PC-DMIS session will be left in an unstable state and should be terminated. The default tessellation multiplier value is 1.0. Setting a tessellation multiplier of 0.1 will result in a 10 to 20 percent increase in the memory required over the default value of 1.0. Decreasing the tessellation multiplier further to 0.01 will result in an additional 50 to 65 percent increase of memory required.
1 GB of video RAM
CPU
2 GHZ or higher Duo-Core processor
Graphics
For desktops: Nvidia Quadro K620 graphics card For laptops: Nvidia Quadro K1100M graphics card The graphics driver must support OpenGL 3.0 or higher. A warning message appears on PC-DMIS startup if the driver does not support OpenGL 3.0 or if your graphics driver is more than a year old.
Hard Drive
2 GB of free hard drive space plus allocated Virtual Memory of 8 times the largest CAD file used SSD drive, HDD 10K, or two disks in RAID 0 mode (high-performance hard disk drive)
Display
Screen resolution of 1280 x 1024 or higher
Connectivity
2 Ethernet ports. (This may be required for specific installations in consideration of local needs, including but not limited to CMM systems where one port is required for controller communications and another for intranet/Internet communications.) 2 USB ports DVD drive HASP key (a physical USB portlock) or a software license
Browser
Internet Explorer version 9
Anti-Virus Software
The Sophos Anti-virus tool was used by Wilcox Associates Inc. while testing PC-DMIS.
The performance of any other anti-virus tool will need to be confirmed by the user. Linklere izin verilmiyor.
Üye Ol ya da Giriş Yap Solutions for CMMs Using RS-232 Communications
If you are installing PC-DMIS on a new or existing computer, but you have an older CMM model that uses RS-232 communications, then you will need to install one of these solutions on your computer:
An external RS-232 serial-to-USB adapter cable plus the serial-to-USB adapter cable driver An internal serial adapter card with serial ports
01 Eylül 2015, 08:32:28
|
1
|
Ynt: Bu program ne işe yarıyor ?
hmm tehlikeli bi programmış...
27 Eylül 2015, 12:09:52
|
1
|
Ynt: Bu program ne işe yarıyor ?
Cısss Resimlere izin verilmiyor.
Üye Ol ya da Giriş Yap
28 Eylül 2015, 19:06:40
|
1
|
|
Sosyal ağınızla giriş yapın
- Toplam Üye: 521
- Toplam İleti: 8,723
- Toplam Konu: 1,552
- Toplam Kategori: 11
- Toplam Bölüm: 38
- En Çok Çevrimiçi: 1,847
|